Your cart is empty.
Your cart is empty. Gas Spouts including Gasket Spout Part Replacement #706.Fits for Gott / Rubbermaid Plastic Can . If only using the Spout & Stopper alone, these May fit of some other Brand Plastic Gas Cans using your own existing screw cap collar for Blitz, Midwest, Scepter, Eagle, Igloo, a few Rotopax and Kolpin. (These do not work with Chilton / Sears Craftsman cans).
The Screw collar will fits Blitz Brand Plastic cans, but you may need to cut off the eyelet holes on side of cap
.IMPORTANT: PLEASE DOUBLE CHECK MEASUREMENTS AND COMPARE TO YOUR EXISTING PARTS.
Stopper Caps with Lanyard for retaining the cap to prevent loss.
Black Rear Air Vent Caps including Gasket & Strap.
Come with yellow (corse thread)and black base caps( fine thread ).
Yellow Vent Caps with RETAINING LIP to prevent from popping out of your can. Easy to install,drill required.Start with an empty can, Drill 1/2" hole at the back of your plastic can above the fill line, insert vent cap and pop it in gently with a rubber mallet.We suggest you drill a smaller hole to start with and work your way up to the 0.3" drill bit. Be sure to drill a straight clean hole don't swagger side to side with the bit so you won't make a bigger hole than you need.
Specifications:
Material:Plastic
Color:White
Size(Nozzle Long):approx 8.07" Long with Gasket is approx1-1/2" Wide
Yellow stopper cap’s inside dimensions are 0.78"
Black Rear Stripe Cap’s dimension is 0.78"
Connected Strings Length is 0.78"
Black fine thread’s inside dimension is 1.88"
Yellow coarse thread’s inside dimension is 1.77"
NOTE: Please check your container outside thread diameter before you make this purchase
JASON B.
Reviewed in the United States on March 1, 2025
Fit good
glenn hanselman
Reviewed in the United States on September 8, 2024
They are great, gas runs so much better. plus the hole to allow air did the trick. The original container was terrible and caused gas to spill out and took for ever to fill tank in engine.
Scott Russell
Reviewed in the United States on July 30, 2024
Does the job as it should. As it turns out I have two five gallon jugs that each require a different thread, but this kit has both, so that was great. The valve for the back of side of the jug was a breeze to install and works great. The only issue I have with the kit at all was that the nozzle is a bit smallish for my taste, and the cap doesn't stay attached when you unscrew it and start to pour fuel. It tends to either fall off, or be in the way. I've gotten in the habbit of just taking it off completely and laying it aside, but it would be good if they'd make the retainer strap longer and make it fit tighter to the nozzle so it stays attached. But over all it works exactly as I'd hoped as far as pouring fuel into implements. I'd recommend it.
Michael Robison
Reviewed in the United States on December 14, 2024
I live in Kalifornia, and you just can’t buy a gas can nozzle here without it being one of those jobs that HAS TO HAVE a button you push, prior to pulling the nozzle back (like you are cocking a gun) so that it can dispense fuel. The springs always break, leaving the nozzle inoperable. Prior to the spring breaking they start to leak, which is contradictory to the whole idea of these “Cali approved” nozzles which are “supposed” to cut down on spills, fume pollution, etc. I ordered this kit, fixed my 2 inoperable cans and have been enjoying them ever since. It’s crazy I haven’t spilled a drop since getting these, but was constantly spilling gas with the crappy “Cali approved, environmentally safe” nozzles. This is a serious upgrade.
Almco
Reviewed in the United States on December 11, 2024
Fits well and works like it should.
Anderson
Reviewed in the United States on December 11, 2024
These things are worthless, don't waste your money. The spout don't flex and it ends up pouring your gas on the ground....Grrr, what a waste!
wr
Reviewed in the United States on October 23, 2024
The pour spouts are short. 2 inches shorter than the original so I'm using that, but this is on a 6 gallon can. The collar fits tightly and the vent cap screws on and seals properly. The snap vent caps have been added to some modern PIA cans and work perfectly.
K. Kline
Reviewed in the United States on June 20, 2021
This product fits the opening like a glove. But if you manual bend the hose it has dislodged from the threaded cap very easily several times leaving gasoline on the floor, shoes, hands etc.. Needs larger flanges. May work better if I go to the hardware store and buy a better gasket but at the time of this review I have not done that yet.
Recommended Products
