Your cart is empty.
Your cart is empty.Product Description
2.4G RF Remote Control Traffic Light Controller Sequencer with 50+ Sequences
2.4G RF remote control traffic lights with 50+sequences for freely programmable traffic light delay time, independent 3-channel solid-state relay output, long silent lifespan, simple operation, intuitive display, safe and reliable
The main functions of the main control board include:
1. DC 5V isolated stabilized power supply.
2. Highlight the 3-digit LED digital display.
3. Red, green, and yellow light delay time adjustment.
4. Rotating encoder, traffic light sequence mode selection and numerical increase or decrease.
5. RF 2.4G remote control traffic light transmission module.
6. Intuitive traffic light LED output display.
7.stop light Independent 3-channel solid-state isolation relay output.
The main functions of the slave control board include:
1.The parameter function adjustment is basically similar to the main control board. When the slave control board is not powered on, it can be operated on the main control board. After the slave control board is successfully paired and powered on, it can only be operated on the secondary control board.
2.The power supply is TYPE-C DC5V.
Power Up
LED Digital tube display "H-. -."
RF 2.4G Pair
1.Not paired successfully, LED flashing.
2.Only when the pairing is successful and the LED light remains on can data be sent to the main control board normally.
Traffic Light Sequence Mode Selection
1.Long press for 3 seconds, the LED light will light up to select the sequence mode, with serial numbers 1-50.
2.The counterclockwise rotation value decreases, while the clockwise rotation value increases.
Red Light Time Set
1.Long press the S2 button for 3 seconds, the D6 LED light will remain on. Rotate the encoder to adjust the red traffic light delay value from 0~250 as needed.
Yellow Light Time Set
1.Long press the S3 button for 3 seconds, the D7 LED light will remain on. Rotate the encoder to adjust the yellow traffic light delay value from 0~250 as needed.
Green Light Time Set
1.Long press the S4 button for 3 seconds, the D8 LED light will remain on. Rotate the encoder to adjust the green traffic light delay value from 0~250 as needed.
Tyler Ayers
Reviewed in the United States on February 7, 2025
Very good customer service, one of my pieces wasn’t working and I called Amazon and they overnighted the piece for me because it wasn’t going to be till March till I received it!
Mike
Reviewed in the United States on February 3, 2025
We had an antique traffic light that we rewired and use this controller for in our game room and it works beautifully looks good and does what it’s supposed to do very happy with the remote. We used a 3-D printer and printed a case for it so that motherboard was able to sit in a case and it worked well
Customer
Reviewed in the United States on February 12, 2025
With over 50 flash patterns, you can make this work with any traffic control device to achieve the effect you are looking for. I am only using the main board to control a traffic signal, haven't had a need for the slave board at this time.The programming and wiring instructions were fairly easy to understand. You will be up and running fairly quick. This remembers the prior setting when the power is turned off. It will come back on to what was last programmed.I would prefer self adhesive PCB mounting pin standoffs for the installation. This board can be mounted inside the traffic light for a clean looking install.
Shanae T.
Reviewed in the United States on December 16, 2024
very easy to follow directions
Mary G
Reviewed in the United States on November 9, 2024
Husband got an old traffic light from somewhere, and is happy with this light sequencer. He is able to get the traffic light to light up, in different patterns and sequences. Husband is planning to get three LED daylight bulbs instead of using incandescent high wattage bulbs, which is more efficient for the light. Instructions are included and are very clear.
Customer
Reviewed in the United States on November 20, 2024
I love the slave board so I can change the light sequence without getting up on a ladder 16 feet in the air. I use a smart outlet to power the board so the power gets cut remotely. This board also saved my time I set for each light to stay illuminated between power cycles.
Colt
Reviewed in the United States on November 16, 2024
The media could not be loaded.
david k. walker
Reviewed in the United States on October 9, 2024
Main board works great but could not get slave board to work. Will not light up or do anything with power going to it, but really dont need. Just going to use main board
Recommended Products