Your cart is empty.
Your cart is empty.Product Description
Make the most of your Dremel rotary tools by using our innovative & extensive line of rotary accessories and attachments. Whatever your project, we’ve got the perfect solution for you. Dremel attachments fit onto your rotary tool to give it a dedicated function. Whether you’re looking to carve, engrave, cut or grind, there is a Dremel attachment to get the job done. The innovative Dremel Circle Cutter & Straight Edge attachment makes it easy to do more with your go-to rotary tool. Not only does it attach easily to the Dremel rotary tool and cuts perfect circles from ¾ In. to 12 In. in diameter, but its straight-edge guide allows for routing or cutting in a straight line. The depth adjustment allows for easy setting of the correct cutting depth. Compatible with most Dremel corded and cordless rotary tools and backed by a 1-year limited warranty.
From the Manufacturer
This innovative attachment is the simple way to cut circular holes in many types of materials. The 678-01 Circle Cutter and Straight Edge Guide attaches easily to the Dremel High-Speed Rotary Tool and cuts perfect circles from 3/4-inch to 12-inch in diameter. The Circle Cutter has convenient measurement guides in both-inches and centimeters, so you can cut out the right-sized circle every time. The Straight Edge Guide allows routing or cutting in a straight line.
wrkrbeee
Reviewed in the United States on January 9, 2025
Take your time and you will create great circles with this product.
JM
Reviewed in the United States on September 27, 2024
Jig worked great for the project I purchased it fop. The bit felt cheap when I opened the box and sure enough, it broke its first time out.
Librado Morales
Reviewed in Mexico on September 22, 2024
Funciona muy bien y sirve para lo que promete muy bien.
SChain
Reviewed in the United States on June 13, 2024
This is my second time purchasing this tool because I misplaced the first one. I used this to cut out round speaker holes for both HDF boards and ceiling boards. Of course HDF board take longer time to cut and after a couple of wholes (6" diameter) the cutting drill bit became somewhat dull. Cutting the ceiling boards is like cutting butter with a sharp knife, very easy and accurate cuts. It takes a little practice to figure out how to setup the position of the drill bit to a precise cut, but once you figured it out, it's pretty easy to setup. I recommend this tool.
Customer
Reviewed in the United Arab Emirates on March 9, 2024
جيد ولكن السعر مرتفع كثيرا
坂本 隆治
Reviewed in Japan on February 25, 2024
ブロックのR取りに使いました、片手操作でも正確に出来ました。
Customer
Reviewed in the United States on December 23, 2024
Good
Sunshine
Reviewed in the United States on November 6, 2024
This dremel accessory worked out perfect for a small project. No regrets in purchasing. Outcome was great!!!!!
Tez Customer
Reviewed in Australia on October 12, 2024
Good quality as always with Dremel,makes things so easy,when cutting circles,or straight lines.Very handy to have with Dremel Tool
Jon
Reviewed in the United States on December 28, 2023
Using this circle cutter with straight edge guide is a great way to turn your dremel into an even more valuable power tool. The circle cutter has worked flawlessly cutting very clean and quick circles/holes. The alternative is to purchase very expensive hole saws that require a major drill for the larger and deeper holes. The dremel and spiral saw bit will allow you to cut very large holes quickly. Set up is a snap and the center point adjustment is super easy to set without any special tools. The hole sizing gauge is a bit general, but if you need a precisely sized hole, I use a tape measure to set the radius by measuring from the far side of the spiral bit to the center of the pivot point. The straight edge guide turns your dremel into a small router that you can use to do all sorts of helpful cuts. Often, whenever I am away from my router table, this is my go to tool for cutting a small and simple dado or rabbit, or cleaning up an edge. I love this attachment!
Lee Anne
Reviewed in Canada on November 8, 2023
We bought this to cut hole in our easedrops to out in our pot lights, it worked perfectly!
Jai Sri Astrology
Reviewed in the United States on March 14, 2022
I am so thankful I finally found one of these Dremel accessory attachments circle cutters I have been needing something like this for so long I did not want to spend an arm and a leg to buy a router and in my artwork I am constantly needing to cut circles either out of the center of a piece of wood or cutting an outer circle into a piece of wood I have three different dremels and I thought surely this thing will fit on one of them I was a little concerned about the sturdiness of the wood cutting bit that came with it because I was cutting through an half inch piece of plywood however after I set it up and started my pilot holes and started cutting into the circle of wood it went smoothly the bit held up great and I cut a perfect circle out of the center of my wood I even turned around and tried it on a plastic decorative plate and it worked great on there so I would highly highly recommend this accessory if you are needing to cut circles and you don't want to spend an arm and a leg on a humongous expensive router this definitely worked I even bought a couple of extra wood cutting drill bits for my Dremel which is always good to have on hand because you never know when you'll break one but overall this was a great great buy for an excellent price
sky
Reviewed in the United States on November 17, 2018
I used this to cut holes into 1/8" MDF board as a template and two 6061 aluminum 1/4" sheets. You really have to make sure all the screws are securely tightened otherwise you will get a lot of wiggling. Don't use this if you actually need to use the circles. The actual hole is cut more accurately than the leftover material. You are more likely to ruin the circles than the holes. Take it slow and hold the tool tightly otherwise the Dremel bit can get caught on the material and ruin your cut. The bit that comes with the tool eats through wood very easily but if you are working with metal you have to be patient and take it extra slow otherwise you can break the bit.The description says you can cut as small as 3/4" in diameter but the smallest I was able to cut with this was a little over 2" in Diameter. The screws on the tool retainer get in the way of the center pin making the tool really wobbly and unstable if I go smaller than 2".The plastic holder that you screw your tool into is very thin and will easily split if you accidentally over tighten your tool. Also the mechanism used to adjust the height of the tool is kind of flimsy and doesn't feel very secure. I got a lot of vibration in the tool if I set the height too high but that could also be because I was primarily working with 6061 Aluminum.Overall its decent if you need something quick and cheap but for anything that needs serious work just get a drill press or better yet a router. It will save you a lot of time and will produce better quality work.
Recommended Products
