Your cart is empty.
Your cart is empty. ✔ Meets/Exceeds: ASME 18.3-12.9
✔ Screw Head : Socket Cap ; Screw Drive: Hex Socket
✔ 12.9 Alloy Steel,Min. Tensile Strength 176,900 psi
✔ Easy to store: These screws come in an easy-use storage case
[ Sizes ]---------[ Head Height ]-----[ Thread Length ]------[ Total Length ]
#8-32 x 3/8"--------0.164"-----------------3/8"----------------0.54"
#8-32 x 1/2"--------0.164"-----------------1/2"----------------0.66"
#8-32 x 5/8"--------0.164"-----------------5/8"----------------0.78"
#8-32 x 3/4"--------0.164"-----------------3/4"----------------0.91"
#8-32 x 1"----------0.164"------------------1"------------------1.16"
[ Package Contains: ]
#8-32 x 3/8"--------20 Pcs
#8-32 x 1/2"--------20 Pcs
#8-32 x 5/8"--------20 Pcs
#8-32 x 3/4"--------20 Pcs
#8-32 x 1"----------20 Pcs
Total-------------100 Pcs
About Hex Socket Drive
Hex Socket Drive, also known as Internal Hex Drive, have a hexagonal hole in the center that requires an Allen key, also known as a hex key or Allen wrench
About Socket Cap Head
Socket Cap Head , also known as Allen head, have a recessed drive, and are commonly used when there is not enough clearance for a conventional wrench or socket. They are fastened with an Allen wrench, which is also called a hex wrench or hex key
corvos
Reviewed in the United States on February 3, 2025
A good selection of #8 allen head screws.
Outdoorguy
Reviewed in the United States on February 24, 2025
If you've ever tried to mount a Mossberg shotgun stock on a Mossberg 500, you need this bolt! And, you will not find one of these in a hardware store or home improvement store! The most infuriating thing is to get a stock for one of these shotguns and the bolt doesn't come with it. This bolt fits the bill perfectly. The existing bolt on a pistol grip is much shorter, and the Mossberg stock has a long hole this bolt fits down into, then an even longer pilot hole this bolt goes through. The problem is, a regular 1/4" hex bolt has a head which is too large to fit inside the larger pathway hole which is where these cap screw bolts come in handy. A single OEM bolt costs as much as this set, so now I've got spares. You'll just need to add an extra flat washer or two under the head to avoid over threading and interfering with the tang safety. Two additional lock washers did it for me). These bolts are 5-15/16" from the base of the head to the end of the threads, and the OEM bolt is 5-1/2", hence the extra washers. There's not stop, so be careful. Thank you for stocking these! Highly recommend.
Welshie39
Reviewed in the United States on February 2, 2025
Allows me to use photographic mounting hardware like Erector set.
Customer
Reviewed in the United States on September 12, 2024
Dimensionally correct. Good product.thanks
Rod
Reviewed in the United States on June 16, 2024
Fine and dandy.
CMYK Josh
Reviewed in the United States on June 15, 2024
We use this type of screw quite a bit on printing presses. The press manufacturers sell these screws at tremendous markup so I get them here. These work as well as the OEM screws that I used to pay a fortune for. For all I know, they buy these and repackage them.
Larry
Reviewed in the United States on October 21, 2024
assortment was convenient and at a low cost. I was in need of one 1/4-20 bolt, so I bought this assortment instead of going to the local hardware store.
Robert Krummel
Reviewed in the United States on January 7, 2024
After using a couple I found they measure the length of the bolt including the head where most bolts or measured overall with out the head.
JC
Reviewed in Canada on April 1, 2022
Good little set of hex head screws for use on small electronics, hobby items and small screw applications. Metal quality is good, with no thread damage or signs of degredation when torqued to 45 in/lbs. Shipped fast and already put to use.
Recommended Products
