Your cart is empty.
Your cart is empty.Makita Ultra Thin Cut-Off Wheels are .032" thick which is 20% thinner than most competitor wheels. These wheels are perfect for making cuts in metal and stainless steel pipes, sheet, and channel
Djoss76
Reviewed in Belgium on September 13, 2024
MagnifiqueLa découpe est excellente et extrêmement résistantDécoupe très précise et fineC'est du Makita, donc bonJe recommande
Rudolf-Franz Smuda
Reviewed in Germany on June 18, 2024
Sehr Gute Scheiben.
Mats Johansson
Reviewed in Sweden on December 31, 2024
Fungerar bra
ENF
Reviewed in the United States on December 21, 2024
I used this wheel to cut through a 25' damaged steel heavy corral gate and divide it into 6 sections to enable moving it for scrap. I used one wheel that was barely worn 1/8" less when I was done. The wheel cut through the steel like butter and the steel was 10ga. so it was not a light gate. It took me about 18 minutes from start to finish to go through the gate and make 6 uniform cut gate sections, so it was light enough to handle. These wheels are not cheap but since I was able to complete the entire task and barely used 1/8" off the wheel these are well worth it!
Miguel
Reviewed in the United States on December 1, 2024
These cutting discs slice through mild steel quickly and efficiently. I used them on 1/4" thick tubes with complex angled cuts that caused other discs to break apart. These, however, held up exceptionally well.
Happy Camper
Reviewed in the United States on November 5, 2024
Wrong product for my grinder by the same manufacturer. Wasn’t advertised correctly.
Ayanajansen
Reviewed in the United States on April 3, 2024
Good stuff here no worries
Dragutin
Reviewed in Germany on June 7, 2023
OK
Arvo
Reviewed in the United Kingdom on December 4, 2023
Fitted one of these to add to my Makita angle grinder, It cut through a thick gate hinge easily, so I'm happy with it!
OlWhiteBeard
Reviewed in the United States on October 30, 2023
Best cutters I have used. They are really thin, so the cut is narrow and they cut fast. Just let them work and do not push them hard into the cut. These are now all I use.
Dr. T
Reviewed in the United States on August 7, 2020
These Makita cutoff wheels have a little bit of magic in them. I have tried several different brands and never get as good results as these. The super thin material is surprisingly sturdy in steel, aluminum and plastics. Wear is really not an issue if you let the wheel do the cutting. Some people like to push the wheel into the cut, if you do that you will have very short life from these. If you let the wheel do the work they will cut tremendously and have ridiculously long life. When I say ridiculous, I cut 18 feet of 1/8" x 1 1/2" plate steel lengthwise with one wheel. Totally the wrong tool for that but I was in a bind out in a field and it worked flawlessly. Makita saved the day.
TonyTheToolGuy
Reviewed in the United States on May 31, 2020
Once you try these, you won't use another similar-sized cutoff. Made in Japan. Extraordinarily thin cut-off wheel for extremely fast cuts that is also flexible so you can deform it to cut flush. I buy the 5" models.I have had a few breaks after deforming them for too long during flush cutting, but I knew I was abusing them, and the breaks were always just the center hub separating from the disk, no drama, not damage, and no injury. I've used over a hundred of these and never had one break apart and throw pieces. They have never been dangerous and I don't run a guard. I'm using a speed-controlled Makita 12amp 9564CV 5" grinder or a Husky brushless 18v 4.5" grinder with them. I typically run the Makita at full tilt, so about 10.5k RPM.You will be blown away at how fast these cut and how well they hold up. With the cordless, they really get you a lot more cuts per battery charge.
Bvr
Reviewed in the United States on December 18, 2020
These are exceptional blades for cutting metal ! I have used a thousand other cutoff wheels and worn out 20 grinders over the years . How about getting 10 crosscuts and a couple of rips on roof metal sheets from one $1.60 wheel. I have cut 1/2" x 6" mild plate and got 6 cuts with a cordless grinder. The thin kerf and high quality produce effortless cuts and when a failure occurs from abuse, the wheels fail at the hub and never shatter. Never force these, let them grind and they last better than most
Recommended Products
