Your cart is empty.
Your cart is empty. Mounting Hole Size: 22mm
Lens Color: Red
Lamp Type: LED
Lamp Voltage: 110V 120V AC/DC
Depth Behind Panel: 1.53"
Jerry from Chiswick
Reviewed in the United States on June 15, 2023
I bought 2 one red, and one green. I purchased to replace another pair that displayed the voltage and not just a red or green light. Unfortunately those were not visible in daylight, and barely at night. This is for my garden lighting. The control is 50 feet away down a narrow obstacle course beside the house. Red there is power at the control box, green there is power to the garden lights and I don't have a power problem. Most likely a WiFi or software issue. The lights save me a lot of time and effort. It remains to be seen if the plastic lenses hold up in the Las Vegas heat and sun. Many times they will just disintegrate. I will update as necessary.***************************************I neither received nor solicited recompense in any form for this review. Solicitations to change or "enhance" reviews are always reported to Amazon without exception. Free items or money are joyfully accepted, THEN IMMEDIATELY REPORTED TO AMAZON!! THANK YOU!!!! The observations are my own without any outside influence or input. Your experience may differ from my own! Do your own research and comparisons prior to purchasing, don't rely solely on my observations. I recommend purchasing only from Prime sellers as my experience with "marketplace" sellers has been mostly negative, often drop shipping from China to the USA so it has a USA postmark. That said, do your own research prior to purchasing any products from the Internet!?
Brian Tamburelli
Reviewed in the United States on May 9, 2023
I wired it up into a cord that's wired to an outlet that's wired to a switch. I mounted the light into a project enclosure. This tells me that the solder sucker is on.
Gray One
Reviewed in the United States on February 27, 2021
I purchased both the green and red to retrofit a control panel. Initially I planned on crimping some insulated spade terminals onto wires and connecting the wires to the fixtures using the screw terminals and crimping a compatible 1/4" male push terminal on the other ends of the wires. Then I noticed that when I took the screws out, that it looked like I was left with a compatible male push terminal connection. However when I tried to use them this way, one side worked but the other side pushed in - it was a a tight fit, and the terminal wasn't designed for the amount of pressure I put on it to connect it up. So I went back to the idea of crimping a round (with a hole) spade connector on a wire for my connection to the light using the screw terminal. Afterwards I used some 7/8" heat shrink tubing to insulate the connectors where I attached the wires. If you use heat shrink tubing - be careful to just cover the terminal area or the tubing will prevent you from removing the back mounting ring. I found that I could work the mounting ring over the heat shrink tubing by slowing twisting it off. Once all connectors were attached to the wires, I installed them into the control cabinet and was very impressed with how well these worked. They are bright enough to use with room light. I picked these over others for sale on Amazon because I didn't have to worry about using a current limiting resistor because it was built into it. Over all I am very pleased with these and might use them for a new project. The only reason I gave it 4 stars and not 5 was because I couldn't use them as if they had push terminals. Ignoring that I give them 5 stars. I also like the fact that replacement LED bulbs are available for these fixtures.
Tn Vol
Reviewed in the United States on April 7, 2021
Way too dim. Somebody had upgraded the LED bulb to a brighter one. Anybody got a part# for the brighter replacement bulb?
6strings
Reviewed in the United States on April 9, 2018
I like these indicators, they look nice! Not too bright - more of a soft glow, but I can see the lit indicator from across the room, and that is exactly what I was looking for. I really like that they have screw terminals. Hint: Use solderless (crimp) fork terminals on these - that works much better, and you can crimp 2 wires into each terminal if needed to parallel wire this to something else. Like having a built-in terminal strip in your project. I use these with the Uxcell 4.92 x 6.89 x 3.94 gray plastic enclosure, and these indicators look so good on it!
skmcfadden
Reviewed in the United States on March 6, 2015
needed an indicator light to show us that our extremely quiet exhaust was still running, when we shut down at the end of the day...worked like a champ...very cost effective solution
John
Reviewed in the United States on June 4, 2014
Just what I wanted. They were easy to incorporate in our daylight sensing, outdoor light control box to show when the lights were on properly. I plan to us the 2nd one to indicate when a drain pump is on when needed.
Scott B.
Reviewed in the United States on April 9, 2014
Used on my brew panel. Good quality lights with colored LED bulbs. I purchased the 240 and 120 volts and was happy with both.
Recommended Products
