Your cart is empty.
Your cart is empty.4.3 out of 5 stars
- #30,853 in Home & Kitchen (See Top 100 in Home & Kitchen)
- #22 in Vacuum Attachments
Product Description
More Replacement Parts for Shark 2500 and 2800 Series
April mead
Reviewed in the United States on February 5, 2025
Some of the parts need extra "help" getting into place and do not last as long as the original parts. They fall off and I have thrown some away because they just did not fit and grabbed another from the set and it worked. I have no idea why one will work and one won't other than quality control is lacking. So you WILL go through these much faster than OEM, but they Still are cheaper so I will buy again. I just wish I did not have to replace these as often and that they all were of the same quality. The quality is definitely sub par. I placed another order asap upon putting my new brush roll in because it is so tight that I do not think it will work. I had to toss the last one after 3 months- It was shredding at the webbing and clogging the machine.
FW
Reviewed in the United States on February 26, 2025
Filters brushes and rollers are perfectly paired to maintain the shark robot vacuum in top operating condition. Easily replaced with T9 torx bit and P0 Phillips bit. Quality of the parts are equal or better than OEM parts. Recommend these to other shark Matrix robot owners.
JDK
Reviewed in the United States on February 17, 2025
This replacement kit has been flawless!!! Having two Old English Sheepdogs and two cats who shed, shed, shed, we replace all the pieces every month and Dustbin Bieber and Clean Latifah run just like new - quiet and cleaning like the beast she is!!! Have zero problem with these replacement parts!!!
weldre
Reviewed in the United States on February 11, 2025
We get what we pay for with cheap aftermarket service parts. The filters fit and time will tell how well they actually filter. However the roller/brush assemblies are too small to fit securely as the original brush does. The replacement roller/brush is loose and moves up and down and side to side when installed. This condition will create wear to drive components in the Robot and therefore I will not be using the roller/brush assemblies.In reading reviews on replacement roller/brushes a common complaint is noise. Noise would be a direct result of the brush being loose and not fitting correctly.
Lorie Harrell
Reviewed in the United States on January 12, 2025
I purchased these parts so when I wash my existing parts to three shark robots I can dry the old ones out and replace them with these parts. They all fit and work like originals. If you don't have a Shark Robot vacuum cleaner but one! saves so much time. My first shark was purchased in 2021 during covid as I could not get out of bed to vacuum. My husband was holding up the whole household and he didn't have time to vacuum. He purchased two and then my mother gave me hers.
David J.
Reviewed in the United States on August 18, 2024
So started looking and it was a nightmare trying to figure out what parts correlates to my model #. For those wondering mine is AV251WAXUS. This kit everything else beside the main roller brush works but you can make it work with the old roller. I’m going to explain the pictures above to try to help.Instructions:1. You can pull the spinning piece off your old roller. 2. Then go ahead and pull the plastic end caps off3. You can then slide out the brushes and the fabric from the old rolled and through them away, but pay attention to the orientation of how they go in.4. Repeat process 1&2 on new roller.5. You can then slide out the new brushes and fabric.6. Install the new brushes and fabric into the old roller.7. Put the ORIGINAL plastic caps back onto the roller8. Snap the rotating piece back on.9. Install it back into the vacuum.Now it will fit and work flawlessly as intendedJust wanted to help someone else who may have the same issue.For that reason alone I can only give it 4 stars due to the dimensions being off.Also if you install the new roller without the changes it will be super tight and will give you an error that the roller brush it stuck.
Dennis
Reviewed in Canada on August 13, 2024
Needed some replacement filters for our Shark AI. The filters fit perfectly and the vacuum is running like new again! However the brush roll seems rather tight.Update: I had to remove the brush roller as it created too much friction from improper fit. It was draining the battery and getting stuck a lot. Purchased a separate replacement brush roll from a different manufacturer and it works well.
jojo
Reviewed in Saudi Arabia on May 26, 2024
ممتازة لكن مو نفس جودة اللي تجي مع المكنسة الفرشة والريش
Be more furgile
Reviewed in Canada on March 22, 2024
Makes easier when maintaining the robot vacuum being able to just switch out a filter or brush etc. We can just swap out a part so the vacuum can continue to clean or charge after it has completed the cleaning. We can inspect the part or filter to see if it can be cleaned and reused later. If the part is unusable then discard it but there’s still spare parts in the shipment to use.
Dr. J
Reviewed in the United States on March 19, 2024
This is an all-in-one kit for a group of different models, so not all parts will work with all models. For my AI (don't have the exact mode #, but I bought it from Costco), that meant the black filters are useless, but I believe every other part will work.I bought this kit because our model is around 1.5 years old, and I keep getting "dust bin not installed" or similar errors. From experience, I find these are usually related to a clogged filter, or rather the base tries to suck the debris out of the vacuum unit, and senses a low pressure differential which it then INTERPRETS as something not being installed. This is particularly frustrating when you're trying to solve a problem! I was also getting a fair amount of the vacuum "flap" on the vacuum unit being propped open with small debris that should otherwise be cleared out - that was also a signal that the base just didn't have the ability to empty the vacuum unit.All this said, there are a few filters in the unit which you need to clean regularly depending on what you have in your home. For us with a husky, that means cleaning things a couple times a week. Don't forget the filter in the base unit that's under a cover on the top left side!At any rate, our unit was getting tired - in addition to the filters, the beater bar was also..... beat. The bars in this kit fit just fine, and I anticipate that the unit will clean better, as our old beater bar was so worn I doubt it really brushed the floor like it should.For the cost I think this is a great value.
Valynn Seraphin
Reviewed in Canada on December 22, 2024
It does not fit the 2610 properly, the brush roller is too tight and continues to say "My brush roller is stuck."Yes I have disassembled and cleaned everything fully. You can tell that the measurements are off by millimeter or so.
Cheryl Weatherford
Reviewed in the United States on September 4, 2023
These parts fit perfectly. It was a guessing game which part number was correct since nothing matched the Shark I’d bought at Costco. In one set of replacement parts that was supposed to be the same as these but were much cheaper the roller door didn’t fit. These fit. Wish they were less expensive but it appears you get what you pay for. My robo vac is now happily working same as out of the box.
Alex
Reviewed in Canada on December 11, 2022
I have been looking for replacement parts for my Shark AI robot vacuum since I got it. This kit is great, replaced all the parts that came with the kit, everything fit perfectly. The round Foam filter is slightly shorter, but it still works just as well. The Main brushroller sounds quiet and the vaccum ran one cycle with no issues. Will be ordering these replacement parts again when needed!
Recommended Products