Your cart is empty.
Your cart is empty.Product Description
Steve Kicinski
Reviewed in the United States on March 8, 2025
excellent quality replacement for an inferior part.
Dee Anne K
Reviewed in the United States on February 25, 2025
Defective or poor quality - returned. They wanted it returned for a refund, so I wrapped up this oily unit and sent it back.
William
Reviewed in the United States on January 28, 2025
Fit well, no leaks. Only issue I had was that the dip stick fit super tight and the oil cap that came with it was kind of cheap material.
automodealz
Reviewed in Canada on September 3, 2024
Oil Cap is a terrible flimsy design, gets damaged and oil leaks all over the place. no other caps fit and cannot find one that fits this cover.
ken f.
Reviewed in the United States on August 17, 2024
As said in other reviews oil filler cap is a bad fit. Use your old one and replace the O-ring form the new one. Dip stick is a tight fit but that is good. The aluminum cover is what the manufacturer should have used
Paulk
Reviewed in Canada on May 27, 2024
Fairly simple installation, no leaks, so far so good,
sirous safaei
Reviewed in Canada on March 22, 2024
good product for money
jdogpat
Reviewed in Canada on February 8, 2024
This valve cover appears to be a quality replacement for the leaky one on my 2014 Cruze. It is, however, not made of aluminum as is claimed in one of the pictures in the listing. It is plastic like the OEM part.
David
Reviewed in the United States on December 28, 2024
2014 Buick encore.Installed by a Buick dealership mechanic .Put a felpro gasket on it .No leaks from the cover and gasket area..However the oil fill cap leaks and does not seal .The cap does not seal properly!!!!Leaks from oil cap .Trying to contact Miliparts !!
Passion4singen
Reviewed in the United States on December 21, 2024
This is a wonderful replacement over the plastic one that comes on the car this valve cover will not chip and break. The downsides and things to watch out for are that the oil cap that comes with?1. It is guaranteed to leak almost immediately.Use the OEM factory oil cap and you will be fine.2. The paint finish is not the greatest, and is blemished with any sort of chemical rather easily such as brake clean or any sort of chemical like that.3. Make sure that the PCV diaphragm cover is fully seated and clipped in all the way around. If not, this will leak and seep oil as well. This valve cover has a serviceable PCV valve diaphragm, which is useful, but means if not properly secured as another oil leak pointI would say the only weak point for this part is the finish on it, which does not affect its dependability and the oil cap, which is a small and easily remedied issue. I WOULD DEFINITELY RECOMMEND!!!
Lex monteiro
Reviewed in Canada on December 16, 2024
The buyer does not inform you to buy a new dip stick of offer one. The original cap does fit as per reviews, however the dip stick does not. I have a 2015 chev Cruze LT and as outlined in description this does not fully accommodate all models outlined. The oil cap provided and original is now leaking. Be cautious when buying this product as it may damage your car
Bandys
Reviewed in the United States on January 24, 2024
This valve cover is made extremely good for the price. Now the oil fill cap is garbage it gets soft with heat. Just use your old one or buy a better one. The valve cover is what is for sell not the oil fill cap. Plus some other brands don't even include them. So I tried a few different brands and honestly this is the best. I have the 1.4 with a lot if miles on it. I did the pcv reroute, intake plug with check valve and was still getting a little too much blowby under hard acceleration. This valve cover was able to seal up the oil that was getting pushed out. Not like the other valve covers I had tried. It's a solid cast aluminum valve cover with baffling. I drilled and tapped the cover to install a catch can and it worked out perfectly.
Daniel Rash
Reviewed in the United States on January 12, 2024
Leaks oil pretty badly and poorly manufactured overall. Oil fill hole doesn't allow cap to seat and leaks. Dipstick hole had to be reamed before the dipstick would fit. Pcv vent doesn't seem to work properly and causes highly fluctuating gas pressure which also causes leaks
Recommended Products