Your cart is empty.
Your cart is empty.Product Description
Milan
Reviewed in the United States on February 14, 2025
Tool is just as described.
Denis
Reviewed in the United States on September 5, 2024
For noob like me the inserts holding like a charm. It was my first tools and my first cut. As you can see even with 0 experience you can practice a lot and not breaking the bank or trying to figure out angle on hss blanks. I think for hobbyists it’s excellent choice. I’ll definitely buy more once those breaks.
Darryl Popove
Reviewed in Canada on May 6, 2024
Right and left tools seem ok for light work but the internal tool leaves much to be desired. The insert seat does not maintain contact with the insert for the length of the insert and does not provide support under the cutting edge where it's most needed.
Farmboy
Reviewed in the United States on May 2, 2024
As in the headline, I didn't expect brand-name quality at this price, but okay for my hobby shop.The description is misleading in two ways. The pictures seem to show inserts mounted in the holders and additional inserts in a small case. Actually the holders were empty and a single insert was supplied for each holder. Also, all the tools are "half inch" (actually 12 mm) except the trigon holder which is "five-eights" (actually 16 mm). That one didn't fit the slots in my 0XA tool holders, so I had to mill it down to 12 mm. Not useful if you don't have access to a mill.As another reviewer noted, the diamond insert didn't fit the right-hand holder. The insert hit the back of the relief without aligning with its retention screw. I was able to mill out the relief with a 1/8 inch end mill and then the insert aligned with the hole but the fit in the holder was sloppy. I think it was intended for a different radius insert.Edit: Actually the insert fit fine, I inserted it in the wrong holder. Fortunately my mod didn't affect the seating of the correct (threading) insert. I have increased my rating to four stars.
1971kid
Reviewed in the United States on May 17, 2024
I have the 5/8 shank with the 11 inserts and so far it's done a great job, the inserts are cutting good and leaving a nice finish, put me down for 5 stars 👍
Muy buena calidad y acabado
Reviewed in Mexico on May 1, 2024
Siempre cortaran mejor las herramientas con insertos de carburo
Customer
Reviewed in the United States on March 5, 2024
Have not actually bored anything yet,but the workmanship of the boring bars looks excellent! Very nice.
Shawn/Texas
Reviewed in the United States on November 12, 2024
Pretty good. Dulls a bit fast but cheap!
Chris C.
Reviewed in the United States on April 22, 2024
My only issue ( and not a big one by any stretch) is I would like a slightly longer shank on the tool for stability when I have to extend the tool out of the qctp for access around a bull nose live center. So far, I've only chipped one insert end, & that was 100% operating error
JTF
Reviewed in the United States on June 12, 2023
I bought the 3 piece set of groove/parting tools with 10 2mm inserts. They are quite good. I had no trouble parting stainless steel which tends to be "sticky". The top title clearly says 5/8" shanks, (which I missed) but the smaller title says 1/2" and 5/8". They are all 5/8" shanks which will not fit a standard AXA 250-101 holder. Luckily I had a couple 250-101T holders which will accommodate a 5/8" shank. The internal tool has flats but will also not fit a 1/2" holder. Worked fine on a 12" lathe. You might have trouble getting them on center for a smaller lathe. And for sure the 5/8" shanks are plenty stiff.
Recommended Products
$74.95
$ 30 .99 $30.99
$163.95
$ 71 .99 $71.99