Your cart is empty.
Your cart is empty.Create your own French doors, window frames and more and add window beauty to a wide variety of projects. A must when building entertainment centers, curio cabinets, kitchen glass cabinet doors and breakfront. One bit will make both rails & stiles and the second will cope the joining ends. The enclosed bearings allow for odd shaped windows and doors. Use with Stock between 7/8" And1-1/2" Thickness. Set includes a beautiful solid wood storage case. Two flute carbide cutters and 1/2" Shanks.
ken talbot
Reviewed in the United States on September 10, 2024
Worked out ok for the Quality of the product
KENNY J BOUDREAUX
Reviewed in the United States on November 27, 2024
Spend a little more and get a set that will do a good job. The profiles do not match up and its impossible to get a good fitting joint no matter how much you try.
cm
Reviewed in Canada on January 7, 2023
would buy again
ottot
Reviewed in the United States on October 6, 2021
Using to make replacements for some rotted muntins in my 107 year old wooden windows. Not a perfect match but close enough.
FRED OSBORNE
Reviewed in the United States on September 30, 2020
made some windows for a old house, the matchup of the pieces was a little off and just couldn't get it all out. glued up and clamps most of it was gone
Karuna
Reviewed in the United States on August 23, 2020
I got this to build a window sash so we could have an extra window in our kitchen. After pricing replacement windows from name brand window places and talking to local craftspeople, I decided to do this myself. This bit made creating a replica of our 80 year old home's original windows pleased me. The bit is sturdy, good 1/2" shaft, is adjustable, and sharp!Made a new window a breeze.
Korey Y
Reviewed in the United States on July 22, 2020
With the help of a table saw I was able to get my muttin close to the original as I needed. Bits came in a nice very nice box and were packaged well. Very sharp as they should be. I can't say how long the edge will hold up for as I didn't need that many feet. I also did this freehand which I do not recommend, but it was good enough for what I needed. Yes that's mahogany!
GT 95
Reviewed in Canada on May 15, 2020
I needed these bits to build a old Sach widow and they worked perfectly for what I bought them for. Especially the price. Very good quality for the price.
Richard
Reviewed in the United Kingdom on March 31, 2020
Can’t do a tenoned window with this set if they’d made them with a removable bearing post on the male bit it would have done both tenoned and dowelled Windows
Doug
Reviewed in Australia on November 25, 2020
I've made five window so far:- 2 of 1400mm x 600mm in hardwood- 2 of 1400mm x 800mm in hardwood- 1 of 450mm x 550mm in softwoodSo far so good. :)
Customer
Reviewed in the United States on November 23, 2020
On first cut (using pine) huge vibration; turned out that a chunk of carbide broke off. Happily, it sailed across the shop, rather than into me.Also bits do not match, so joints do not match. Not usable, not safe to use.
Alicia
Reviewed in Canada on October 2, 2020
I cut off most of the bearing post using a hacksaw while protecting the cutting edge by using a thin piece of wood with a hole matching the post size drilled through it. I then used a grinder to remove remainder of post so that it was below the cutting edge and flush with the top of the yellow body. The bit and post appear to be milled from a single piece. Balance of bit was good following post removal. Be careful not to damage the carbide cutting edges.
Toolman
Reviewed in the United States on October 22, 2010
For the price the joints fit flawlessly.however you must dowel or make a floating tenon to create a strong joint.Perfect for repairing or replacing windows on your old house.The down side: When using a shaper table.The material must be sized perfectly. Because the stiles are shaped from the front and the rails are shaped from the back so if not aligned perfectly the joint will be very out of alignment.With better quality bits all machining takes place from the front of the work piece making for perfect aligning joints even if material thickness varies.all missalignments are on the back of the work.You also cannot create tenons with these bits.However for the occasional window maker they are priced just right.
Recommended Products
$84.58
$ 34 .99 $34.99
$12.99
$ 5 .99 $5.99